Certified Mold Inspector in STUDIO CITY, California
Lab-backed mold testing for Studio City homes and businesses
A Certified Mold Inspector in STUDIO CITY, California gives you a written, lab-backed answer about what is growing in your walls, attic or crawl space. Our licensed mold assessor in Studio City CA walks every room with a moisture meter and thermal imaging camera, documents hidden growth, and hands you a report you can act on or send to your agent. Same-day appointments are available across the 91604 area.
Certified Mold Inspector in STUDIO CITY, California
A Certified Mold Inspector in STUDIO CITY, California is a trained, credentialed evaluator who locates mold growth, identifies the moisture source feeding it, and documents both in a written report with lab results. The inspection is not a sales visit. We map suspect areas with a moisture meter and thermal imaging camera, take air and surface samples, and send them to an accredited lab. Most single-family homes take two to four hours from arrival to final walkthrough.
Studio City properties give mold plenty of places to hide. The 2026 rainy season pushed water into crawl spaces and behind stucco on hillside homes, and decades-old plumbing under Ventura Boulevard bungalows keeps leaking quietly behind cabinets. A certified mold inspection STUDIO CITY California homeowners can trust starts with finding that water, not just spraying the visible black mold growth. If you have smelled a musty odor since last winter, that is your cue to book a licensed mold assessor in Studio City CA before the next storm.
What a Certified Mold Inspection Delivers
A proper inspection turns a vague worry into a documented answer. Here is what you get when our team walks your Studio City property.
Lab-Backed Written Report
Every sample goes to an accredited lab, and you receive the results with species identification and spore counts. The report names each affected area, the moisture source behind it, and a recommended scope of work. Real estate agents, insurers and contractors accept it because it is documented, not guessed.
Hidden Moisture Found Fast
Mold behind drywall or under flooring rarely shows itself. We use a moisture meter and thermal imaging camera to read temperature differences through tile, stucco and hardwood, then confirm with a borescope camera inside the wall cavity. In a typical Studio City home we locate the source in under 90 minutes.
Clear Next-Step Pricing
If growth is confirmed, we price the fix in writing the same day. A single bathroom or attic area usually runs $450 to $1,800 depending on square footage and material. You decide whether to proceed with us or hand the report to another contractor. No pressure, no surprise add-ons.
Protection for Your Sale or Lease
Buyers and tenants in Studio City ask for mold documentation constantly. A certified mold inspector for real estate Studio City California transactions gives you a clean paper trail that satisfies lenders and disclosure requirements. We have supported escrow timelines as short as five days.
How Our Mold Inspection Process Works
From your first call to the final report, here is exactly what happens when you book with us in Studio City.
Phone Intake
You call (833) 929-5837 and describe what you are seeing or smelling. We ask about recent water damage, roof leaks, bathroom humidity and HVAC performance. Within 15 minutes you get an appointment window, a flat inspection price, and a short list of things to do before we arrive, like keeping the HVAC off for two hours.
On-Site Walkthrough
Our inspector arrives with a moisture meter, thermal imaging camera and borescope. We inspect every room, the attic, crawl space, basement, bathrooms and HVAC closet. Suspect areas get photographed and marked. This stage takes 60 to 120 minutes depending on square footage and how many areas need a closer look.
Air and Surface Sampling
We run air samples in affected rooms plus one outdoor control, then take surface or tape-lift samples from visible growth. Samples are sealed, labeled and shipped to an accredited lab the same day. Lab turnaround is typically 24 to 48 hours, and we send you tracking so you know when results land.
Report and Findings Call
Once lab results arrive, we build a written report with photos, moisture readings, species identification and a recommended scope. You get a 20-minute call to walk through it. We explain what is active, what is old, and what the moisture source is, in plain language, not lab jargon.
Remediation Planning
If growth needs removal, we provide a written scope with line-item pricing. That scope covers containment barriers, HEPA filtration, antimicrobial coatings and post-remediation verification testing. You can approve it, adjust it, or take it to another licensed mold assessor in Studio City CA for a second look.
Certified Mold Inspection Expertise You Can Verify
Our inspectors hold IICRC certification and ACAC certification, and we operate under a California Contractors State License Board (CSLB) license and Mold Remediation Contractor license. We have completed hundreds of inspections across the San Fernando Valley since opening in 2025, with a focus on hillside homes, mid-century bungalows and small commercial spaces. Every inspector trains on moisture meter and thermal imaging camera interpretation, lab sampling protocol and California disclosure requirements, so the report you receive holds up with agents, lenders and tenants.
- IICRC-certified inspectors trained in water damage and mold assessment standards
- ACAC certification held by every field inspector on our team
- EPA Lead-Safe certification for pre-1978 Studio City housing stock
- OSHA compliance training for containment and respirator use
- Hundreds of inspections completed across the San Fernando Valley since 2025
Why Studio City Chooses Our Certified Mold Inspector
Plenty of companies will spray something on a wall and call it done. We document, test and report, so you know exactly what you are dealing with before you spend a dollar on remediation.
Same-Day Appointments
Call before noon and we can usually be at your door the same day. Emergency mold testing services are available 24/7 for active leaks, flooded basements and post-storm water intrusion. Our average arrival window across Studio City is 90 minutes for urgent calls.
Independent Lab Results
We do not run our own lab. Samples go to a third-party accredited facility, which means the spore counts and species identification in your report are not influenced by anyone selling remediation. That independence is why agents and attorneys accept our documentation.
Flat Inspection Pricing
You get the price before we arrive, and it does not change based on what we find. Affordable certified mold inspector STUDIO CITY California pricing starts at $299 for a standard single-family home, with larger properties and commercial spaces quoted upfront. No hourly billing, no surprise trip charges.
Report in 24 to 48 Hours
Most clients have lab results and a written report within two business days. If you are in escrow, tell us the deadline and we will prioritize the sample shipment and report delivery. We have turned reports around in under 24 hours for time-sensitive Studio City closings.
What Our Certified Mold Inspection Includes
Every inspection covers the full property, not just the room you are worried about. Here is what is included in the standard fee, and what we quote separately if you need it.
What's Included
Full Interior Walkthrough
Every accessible room, closet, hallway and utility space gets inspected with a moisture meter and thermal imaging camera. We check under sinks, behind appliances, along baseboards and inside HVAC closets. Attics, crawl spaces and basements are included when safely accessible.
Air and Surface Sampling
Standard inspections include two to four air samples plus one outdoor control, and surface samples from any visible growth. Additional samples for large homes or multi-unit buildings are quoted at $75 each. All samples ship to an accredited lab the same day.
Written Report With Photos
You receive a PDF report with labeled photos, moisture readings, lab results, species identification and a recommended scope of work. The report is formatted for real estate disclosure, insurance claims and contractor bidding, and it typically runs 12 to 25 pages.
Findings Walkthrough Call
A 20-minute call with the inspector who walked your property. We explain what is active, what is old, where the water is coming from and what the fix looks like. You can invite your agent, tenant or contractor to join the call at no extra charge.
Remediation Scope and Quote
If growth needs removal, we provide a line-item scope covering containment, HEPA filtration, removal methods and post-remediation verification. Pricing is fixed, not estimated, and you are free to shop it against other licensed mold assessor in Studio City CA providers.
Mold Problems We Solve in Studio City
Most calls we get start with a smell, a stain or a health concern. Here are the situations we handle most often.
Musty odor with no visible growth
Odors usually mean active growth inside a wall, under flooring or in the HVAC system. Ignoring it lets mold spread through the ductwork and into bedrooms within weeks.
We use a thermal imaging camera and borescope camera to find the source behind finished surfaces, then take air samples in the affected room and the HVAC return. Once the source is confirmed, we document it with photos and readings so remediation can target the right area.
Water damage from a roof leak or burst pipe
Drywall and insulation hold moisture for weeks after a leak stops. That trapped water feeds black mold growth and can rot framing behind the wall before you notice a stain.
We inspect within 24 hours of your call, map moisture with a meter, and sample any suspect drywall or framing. If growth is confirmed, our scope covers removal, antimicrobial coatings and post-remediation mold spore testing to verify the area is clean.
Crawl space or basement mold after heavy rain
Studio City crawl spaces sit close to the water table on some streets, and standing water after a storm can feed crawl space mold for months. It migrates upward into living space through the subfloor.
We inspect the crawl space with a moisture meter and borescope, document the extent of growth, and identify the entry point for water. Our report includes a drainage and encapsulation recommendation so the problem does not return next rainy season.
Mold discovered during a home sale
An unresolved mold finding can delay escrow, kill a loan or force a price reduction. Buyers want documentation, not a verbal assurance that it is fine.
We prioritize escrow timelines and can deliver a full report with lab results in under 48 hours. The report is formatted for disclosure and satisfies most lenders. If remediation is needed, we provide a fixed-price scope the buyer and seller can review together.
When to Book a Mold Inspection
You are buying a 1950s bungalow near Tujunga Village and the disclosure mentions a past roof leak.
We inspect the attic, ceiling cavity and any wall adjacent to the old leak with a moisture meter and borescope camera. Air samples go to the lab the same day, and the report is ready for your agent within 48 hours.
You know before closing whether the leak left active growth, and you have a documented basis to negotiate repairs or credits.
Your tenant in a Colfax Meadows duplex reports a musty smell in the hallway closet.
We inspect the closet, adjacent bathroom and shared wall with a thermal imaging camera, then sample the air and any visible growth. If the source is a slow plumbing leak, we document it for your plumber.
You get a written report that supports the repair, protects your disclosure position and gives the tenant a clear timeline.
A hillside home above Fryman Canyon had water intrusion during the last rainy season.
We inspect the crawl space, lower-level walls and any stucco penetrations with a moisture meter, then take surface samples from stained areas. The report identifies whether growth is active or historical.
You know whether remediation is needed now or whether drying and monitoring will resolve it, with lab evidence to back the call.
You manage a small commercial suite on Ventura Boulevard and the HVAC has been blowing a musty smell.
We inspect the air handler, ductwork and ceiling plenum with a borescope camera, then take air samples at the return and in two occupied zones. Lab results identify species and spore counts.
You get a documented HVAC mold assessment and a scope for coil cleaning, duct remediation or replacement, priced before you commit.
Tools and Methods We Use
Tools & Equipment
Moisture Meter
Reads moisture content in drywall, wood framing and subfloor. We use it to confirm active water intrusion behind finished surfaces and to establish a baseline for post-remediation drying.
Thermal Imaging Camera
Detects temperature differences that reveal hidden moisture, missing insulation and air leaks. It lets us scan a full wall in seconds without cutting into drywall.
Borescope Camera
A slim camera that goes inside wall cavities, ductwork and crawl spaces. We use it to confirm growth behind finished surfaces and to photograph it for your report.
Air Sampling Pumps
Draw measured volumes of air through spore-trap cassettes. Samples are sealed, labeled and shipped to an accredited lab for species identification and spore counts.
HEPA Vacuum and Air Scrubber
Used during post-remediation verification and any limited sampling cleanup. HEPA filters capture spores down to 0.3 microns, keeping the work area clean.
Respirators and Tyvek Suits
Standard PPE for any inspector entering a crawl space, attic or confirmed growth area. Protects our team and prevents cross-contamination between rooms.
Containment Barriers and Zipper Doors
Plastic sheeting and zipper doors isolate affected areas during sampling and any follow-up work, keeping spores out of clean rooms.
Methods & Techniques
IICRC S520 Assessment Protocol
We follow the IICRC S520 standard for mold assessment, which defines how to categorize contamination, select sampling locations and interpret lab results. It is the reference standard most insurers and remediation contractors accept.
ACAC-Certified Evaluation
Every inspector holds ACAC certification, which requires formal training in mold biology, moisture dynamics and building science. That training shapes how we read a property, not just how we run a meter.
Third-Party Lab Analysis
All samples go to an accredited independent lab. Results come back with species identification and spore counts, and we attach the raw lab report to your documentation so nothing is filtered or summarized away.
Post-Remediation Verification
After any remediation, we return to run clearance air samples and confirm spore counts are back to outdoor baseline. This step is what closes out an insurance claim or satisfies a buyer's inspector.
How Mold Inspection Works Across Studio City
Studio City sits in a bowl between the Santa Monica Mountains and the LA River flood plain, and that geography drives most of the mold calls we run. Hillside homes above Fryman Canyon and Oakdell Canyon get water pushed against their retaining walls every rainy season, while flat-lot bungalows near Tujunga Village deal with crawl space humidity that never fully dries. The housing stock matters too: most homes here were built between 1935 and 1965, with original galvanized plumbing, unvented bathrooms and stucco exteriors that trap moisture behind the cladding. When you book a licensed mold assessment in STUDIO CITY, we plan the inspection around those realities. We check the crawl space first on flat lots, the retaining wall and lower level first on hillside properties, and the HVAC closet in every home because duct condensation is common in this climate. If you are searching for a certified mold inspector near me Studio City CA, expect us to spend more time in the attic and crawl space than in the living room, because that is where the evidence lives.
Service Areas
Hillside homes with retaining walls and lower-level living space. Water intrusion after heavy rain is the most common call we get here.
Older bungalows with original plumbing and unvented bathrooms. Slow leaks behind cabinets and in crawl spaces are routine.
Mid-century single-family homes with flat or low-pitch roofs. Ceiling and attic moisture shows up after every rainy season.
Mixed residential and commercial buildings. HVAC mold contamination and shared-wall moisture are the most frequent findings.
Denser housing with shared walls and older ductwork. Air sampling in multiple units is often needed to isolate the source.
Local Considerations
Winter rain pushing water against hillside foundations
Drives crawl space and lower-level mold growth from December through March. We schedule inspections in the days after a storm to catch active intrusion.
Summer heat and high indoor humidity
Air conditioning runs hard from June through September, and condensate in ductwork and air handlers becomes a common growth site. We inspect the HVAC closet on every call.
Pre-1978 housing stock with original plumbing
Slow leaks behind walls go undetected for years. Our EPA Lead-Safe certification lets us sample safely in these homes without disturbing lead paint.
Stucco exteriors that trap moisture
Water that enters through cracks or window flashing stays behind the cladding. Thermal imaging is the only reliable way to find it without cutting into the wall.
Colfax Meadows Attic After Roof Leak
A homeowner noticed a ceiling stain after the last rainy season. The attic had visible black mold growth across roughly 40 square feet of roof sheathing, and the moisture meter read 28 percent on the affected framing. The roof leak had been active for at least two seasons.
We documented the growth with photos and lab-confirmed Cladosporium and Penicillium. The homeowner had the roof repaired and the sheathing treated. Post-remediation air samples came back at outdoor baseline levels, and the ceiling stain was patched.
Maintenance & Follow-up
Check the attic twice a year, once after the rainy season and once in late summer. Fix any roof flashing or vent issue within two weeks, and keep attic ventilation clear so sheathing dries between storms.
A 1948 bungalow had a persistent musty odor in the hallway. The crawl space held standing water after winter rains and showed mold growth on the floor joists. Moisture readings on the joists were above 25 percent across a 300-square-foot area.
We documented the extent with a borescope camera and lab samples. The owner installed a sump pump and vapor barrier, and our post-remediation verification showed spore counts back to normal. The musty odor cleared within a week of drying.
Maintenance & Follow-up
Run the sump pump test monthly during the rainy season, keep the vapor barrier sealed, and re-inspect the crawl space every fall before the first storm.
A commercial tenant complained of a musty smell from the ceiling vents. The air handler coil pan held standing water, and the duct liner showed visible growth. Air samples in two occupied zones came back with elevated Aspergillus and Penicillium spore counts.
We documented the contamination and provided a scope for coil cleaning, duct liner removal and HEPA vacuuming. After remediation, clearance air samples in both zones returned to outdoor baseline, and the tenant's complaint resolved.
Maintenance & Follow-up
Schedule HVAC coil cleaning twice a year, keep the condensate pan draining freely, and replace filters every 60 to 90 days. Re-test the ducts annually if the building runs the system year-round.
Certified Mold Inspector Cost in Studio City
Typical 2026 pricing for a certified mold inspection in Studio City runs $299 to $650 for a standard single-family home, and $650 to $1,400 for larger properties, multi-unit buildings or commercial spaces. The fee covers the full walkthrough, air and surface sampling, lab analysis and the written report. Remediation, if needed, is quoted separately with line-item pricing. We do not bill hourly, and the inspection price does not change based on what we find.
Pricing Factors
Property Size
Square footage drives inspection time and the number of air samples needed. A 1,200-square-foot bungalow usually needs two air samples, while a 3,500-square-foot hillside home may need four or five to cover every zone.
Number of Sample Points
Standard inspections include two to four air samples plus one outdoor control. Additional samples, including surface or tape-lift samples from visible growth, run $75 each and are quoted before we take them.
Access Difficulty
Crawl spaces with limited clearance, attics without walkways and enclosed wall cavities take longer to inspect. We quote any access surcharge upfront so there is no surprise on the invoice.
Commercial or Multi-Unit
Buildings with shared HVAC, multiple tenants or more than 5,000 square feet require zone-by-zone sampling and a longer report. Commercial inspections start at $650 and scale with the number of zones.
Turnaround Time
Standard lab turnaround is 24 to 48 hours. Rush processing is available for escrow deadlines and typically adds $75 to $150 depending on the lab's schedule.
Post-Remediation Verification
Clearance testing after remediation is priced separately, usually $199 to $399 depending on the number of zones. It includes air samples and a written clearance report suitable for insurance or escrow.
Typical Investment Range
$299 - $1,400 depending on property size, sample count and turnaround
Actual pricing varies based on project scope and requirements
Value You Receive
You are paying for documentation, not a sales pitch. The report we hand you is accepted by agents, lenders, insurers and contractors, and it tells you exactly where the water is coming from. That is what turns a vague worry into a fixable problem.
Frequently Asked Questions
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsHow much does a certified mold inspector cost in STUDIO CITY California?
Most single-family homes in Studio City run $299 to $650 for a full inspection with lab samples and a written report. Larger properties and commercial spaces start at $650. The price includes the walkthrough, two to four air samples, one outdoor control, lab analysis and the report. Additional samples are $75 each, and rush turnaround adds $75 to $150.
What certifications should a mold inspector have in Studio City CA?
Look for IICRC certification and ACAC certification, which require formal training in mold assessment and building science. In California, the inspector should also work under a CSLB license and hold a Mold Remediation Contractor license. EPA Lead-Safe certification matters for pre-1978 homes, which is most of Studio City's housing stock.
How do I find a licensed mold assessor in STUDIO CITY?
Ask for the inspector's certification body and license type before you book. A legitimate assessor will name their IICRC or ACAC credentials and their CSLB license without hesitation. They will also send samples to an independent lab rather than running their own. We provide all of that upfront when you call (833) 929-5837.
Is a certified mold inspector required in Studio City California?
California does not require a certified inspector for a private home sale, but most lenders, insurers and buyers ask for a documented inspection when mold is disclosed or suspected. For commercial properties and post-remediation clearance, a certified inspection is effectively standard practice. It also protects you in a tenant dispute or insurance claim.
Credentials and Reviews
Certifications
Customer Reviews
We called about a musty smell in the hallway and they came out the next morning. The inspector spent almost two hours in the crawl space and found the source behind a joist. Lab results came back in two days with a full report. No pressure to buy anything, just clear findings and a scope we could shop around.
Used them for a pre-sale inspection on a 1952 bungalow near Tujunga Village. The report was thorough, with photos and moisture readings for every area. Our agent said it was one of the cleanest inspection reports she had seen. Escrow closed on time with no mold issues.
We manage a commercial suite on Ventura Boulevard and had a recurring musty smell from the HVAC. They sampled three zones, identified the growth in the duct liner and gave us a fixed-price scope. Clearance testing after remediation came back clean. Straightforward, professional and on schedule.
Related Services
Explore our other professional services
Mold Inspection Near Me
Same-day mold inspection across Studio City and the San Fernando Valley. We walk the property, sample the air and hand you a lab-backed report within 48 hours.
Mold Inspection Near MeMold Inspection
Full interior mold inspection covering every room, attic, crawl space and HVAC closet. Includes moisture mapping, thermal imaging and a written report with photos.
Mold InspectionMold Testing
Air and surface mold testing with third-party lab analysis. Results include species identification and spore counts, usually back within 24 to 48 hours.
Mold TestingMold Testing Near Me
Local mold testing for Studio City homes and businesses. We ship samples the same day and deliver a report formatted for real estate, insurance or contractor use.
Mold Testing Near MeBlack Mold Inspection
Targeted inspection for black mold growth, including Stachybotrys identification. We document the extent, find the moisture source and provide a remediation scope.
Black Mold InspectionHome Mold Inspection
Residential mold inspection for single-family homes, condos and duplexes. Covers living space, attic, crawl space, basement and HVAC, with lab samples included.
Home Mold InspectionResidential Mold Testing
Air and surface testing for homes in Studio City and nearby neighborhoods. Includes an outdoor control sample and a written report with lab results.
Residential Mold TestingCommercial Mold Inspection
Mold inspection for offices, retail and multi-unit buildings along Ventura Boulevard. Zone-by-zone sampling and a report formatted for property managers and insurers.
Commercial Mold InspectionMold Remediation Company
Full-service mold removal with containment, HEPA filtration and post-remediation verification. We provide a fixed-price scope after your inspection.
Mold Remediation CompanyEmergency Mold Testing Services
24/7 emergency mold testing for active leaks, flooded basements and post-storm water intrusion. We aim to be on-site within 90 minutes across Studio City.
Emergency Mold Testing ServicesSame Day Mold Testing
Call before noon and we can usually sample the same day. Lab results typically return within 24 to 48 hours, with rush processing available for escrow deadlines.
Same Day Mold TestingBasement Mold Inspection
Basement mold inspection with moisture mapping and air sampling. Common in hillside Studio City homes where water pushes against lower-level walls.
Basement Mold InspectionAttic Mold Testing And Removal
Attic mold testing focused on roof sheathing, rafters and insulation. We document growth, identify the roof or ventilation source and provide a removal scope.
Attic Mold Testing And RemovalAir Quality And Mold Testing
Indoor air quality testing that measures mold spores, moisture and ventilation. Useful when odors or health symptoms appear without visible growth.
Air Quality And Mold TestingMold Remediation Near Me
Local mold remediation for Studio City properties. Containment, HEPA vacuuming, antimicrobial coatings and clearance testing, all priced from a written scope.
Mold Remediation Near MeCrawl Space Mold Removal
Crawl space mold removal with vapor barrier and drainage recommendations. Common in flat-lot Studio City homes after winter rains.
Crawl Space Mold RemovalBathroom Mold Removal Service
Bathroom mold removal targeting tile, grout, caulk and drywall. We find the moisture source, remove growth and apply antimicrobial coatings.
Bathroom Mold Removal ServiceToxic Mold Removal
Removal of toxic mold species including Stachybotrys and Aspergillus. Full containment, HEPA filtration and post-remediation verification included.
Toxic Mold RemovalMold Abatement
Mold abatement for larger contamination areas in homes and commercial buildings. Includes containment barriers, negative air machines and clearance testing.
Mold AbatementProfessional Mold Removal
Professional mold removal with documented scope, containment and clearance testing. We handle drywall, framing, insulation and HVAC components.
Professional Mold RemovalMold Cleanup Near Me
Mold cleanup for Studio City homes after leaks, floods or long-term humidity. We remove growth, dry the structure and verify with air samples.
Mold Cleanup Near MeWater Damage Mold Remediation
Water damage mold remediation that starts with drying and ends with clearance testing. We document the moisture source and the removal scope.
Water Damage Mold RemediationMold Spore Testing
Mold spore testing with species identification and spore counts from an accredited lab. Results typically return within 24 to 48 hours.
Mold Spore TestingPost Remediation Mold Testing
Clearance testing after mold remediation. Air samples confirm spore counts are back to outdoor baseline, closing out insurance claims and escrow requirements.
Post Remediation Mold TestingMold Fogging Treatment
Mold fogging treatment using Benefect and Concrobium to treat hard-to-reach surfaces. Often paired with HEPA vacuuming and antimicrobial coatings.
Mold Fogging TreatmentDry Ice Blasting Mold
Dry ice blasting for mold removal on framing, masonry and mechanical equipment. No chemical residue and no secondary media cleanup.
Dry Ice Blasting MoldAffordable Mold Remediation
Budget-conscious mold remediation with the same containment and clearance testing as larger jobs. Fixed-price scopes start at $450 for small areas.
Affordable Mold Remediation24 Hour Mold Removal
Round-the-clock mold removal for emergencies. We respond to active leaks, flooded crawl spaces and post-storm intrusion across Studio City.
24 Hour Mold RemovalOdor Removal Mold
Musty odor removal tied to hidden mold growth. We locate the source with thermal imaging and borescope inspection, then remove growth and treat the area.
Odor Removal MoldBook a Certified Mold Inspector in STUDIO CITY, California
If you have smelled something musty or spotted a stain since the last rain, get it documented before it spreads. Our inspectors are IICRC and ACAC certified, and we deliver lab-backed reports in 24 to 48 hours. Call (833) 929-5837 to book your inspection today.